Submersible sewage pump maintenance and care

In order to ensure the normal use and life of submersible sewage pump, regular inspection and maintenance should be carried out:
1, replace the seal ring: After long-term use in the sewage medium, the gap between the impeller and the seal ring may increase, resulting in reduced pump flow and efficiency, turn off the brake, the pump hoisted, remove the bottom cover, remove Seal ring, according to the actual size of the impeller ring with seal ring, the gap is generally about 0.5mm.
2, submersible sewage pump long-term need, should be cleaned and lifted in ventilated and dry place, pay attention to antifreeze. If placed in water, run at least 30 min every 15 days (do not dry) to check its function and suitability.
3, cable inspection at least once a year, if damaged please give replacement.
4, at least once a year inspection motor insulation and fastening screws, if the motor insulation down to find someone to repair, if the fastening screws loose, please re-tighten.
5, submersible sewage pump at the factory has injected the right amount of oil, used to lubricate the mechanical seal, the oil should be checked once a year. If you find water in the oil, it should be let go, replace the oil, replace the gasket, tighten the screw plug. After three weeks, it must be rechecked. If the oil becomes emulsion, the mechanical seal should be inspected and replaced if necessary.
6, submersible sewage pump operation failure, according to the given troubleshooting methods are excluded, if still can not be resolved, and can not determine the cause, do not indiscriminately disorganized chaos repair, should immediately find someone to repair.

More keyword search: Sewage pump

The Hardness Tester is a hardness tester. Metal hardness measurements were first defined by Ray Ommel's definition of hardness, which means that the material resists the ability of a hard object to press into its surface. It is one of the important performance indicators of metal materials. The higher the hardness in general, the better the abrasion resistance.

Hardness test is the simplest and most convenient test method in mechanical performance test. In order to be able to replace certain mechanical properties tests with hardness tests, a more accurate conversion of hardness and strength is required in production.
1. Dietmar Leeb The Leeb hardness is based on the latest Leeb hardness test principle and is designed using state-of-the-art microprocessor technology.
2. Brinell Hardness (HB) Hardened steel balls of a certain size (typically 10 mm in diameter) are pressed onto the surface of the material at a given load (typically 3000 kg) and held for a period of time. After loading, the ratio of the load to its indentation area , which is the Brinell hardness value (HB) in kilograms force/mm2 (N/mm2).
3. Rockwell Hardness (HR) When HB>450 or the specimen is too small, the Brinell hardness test cannot be used instead. It uses a diamond cone with a vertex angle of 120° or a steel ball with a diameter of 1.59 and 3.18 mm to press the surface of the material under test under a certain load. The hardness of the material is obtained from the depth of the indentation. According to the hardness of the test material, divided into three different situations
HRA: It is the hardness obtained with a 60kg load and a diamond cone press. It is used for materials with extremely high hardness (such as cemented carbide, etc.).
HRB: Hardened steel balls with a load of 100kg and a diameter of 1.58mm are used to obtain a hardness that is used for materials with low hardness (such as annealed steel, cast iron, etc.).
HRC: It is the hardness obtained with a 150kg load and a diamond cone press. It is used for materials with high hardness (such as quenched steel, etc.).
4. Vickers hardness (HV) with a load of 120kg or less and a diamond square cone press with a vertex angle of 136° is pressed into the surface of the material. The load value is divided by the surface area of the material indentation pit, which is the Vickers hardness value. (HV).
5 Knoop Hardness (HK)
Suitable for hardness testing of high hardness materials (general hardness measurement above HV1000 hardness).
6. There are Shore hardness tester
7. Wechsler hardness tester (HW)
Suitable for the measurement of Vickers hardness value of aluminum alloy products.
8 plaster hardness tester
Applicable to the measurement of the hardness of building plaster, the steel ball is placed on the test piece, and the depth of the ball mark under the effect of the fixed load is measured, and the plaster hardness of the test piece is calculated.
The above hardness is only a few commonly used, in addition to Shore hardness, Shore hardness, Barcol hardness, Mohs hardness. Practice has shown that there is an approximate correlation between hardness values and strength values between various hardness values of metallic materials. Because the hardness value is determined by the resistance to initial plastic deformation and the resistance to continued plastic deformation, the higher the strength of the material, the higher the resistance to plastic deformation and the higher the hardness value.

Hardness Tester

Hardness Tester,Automatic Hardness Tester,Digital Hardness Tester,Vicker Hardness Tester

Dongguan Jaten Instrument Co.,LTD(HK TT:Jaten Technology Co.,Ltd ​) , https://www.jatentech.com